sx (asx) ordering information types 1. standard pc board terminal standard packing: tube: 40 pcs.; case: 1,000 pcs. high sensibility relay with guaranteed low level switching capacity sx relays (asx) contact arrangement nominal coil voltage single side stable 1 coil latching 2 coil latching part no. part no. part no. 2 form c 1.5v dc ASX2001H asx2101h asx2201h 3v dc asx20003 asx21003 asx22003 4.5v dc asx2004h asx2104h asx2204h 6v dc asx20006 asx21006 asx22006 9v dc asx20009 asx21009 asx22009 12v dc asx20012 asx21012 asx22012 24v dc asx20024 asx21024 asx22024 compliance with rohs directive features 1. high contact reliability over a long life has been made possible for low level loads. using a low level load (1 mv 10 a to 10 v 10 ma) 10 7 operations were achieved with a static contact resistance of max. 100 m ? (voltage drop of 20 mv, 1 ma, 1 khz) and a dynamic contact resistance of max. 1 ? (measurement delay 10 ms, voltage drop of 20 mv, 1 ma, 1 khz). 2. high sensibility of 50 mw by using the highly ef?ient polar magnetic circuit ?eesaw balance armature mechanism? a rated power consumption of 50 mw (for single side stable type) has been achieved. 3. low thermal electromotive force reducing the heat from the coil enables a thermal electromotive force of 3 v or less. typical applications this relay will be used for the low level load for measuring instruments or others where a stable contact resistance is required. nominal coil voltage (dc) 1h: 1.5v 03: 3v 4h: 4.5v 06: 6v 09: 9v 12: 12v 24: 24v contact arrangement 2: 2 form c type of operation 0: standard type (b.b.m.) asx 2 0 operating function 0: single side stable 1: 1 coil latching 2: 2 coil latching terminal shape nil: a: standard pc board terminal surface-mount terminal (a type) packing style nil: x: z: tube packing tape and reel packing (picked from 1/3/4/5 pin side) tape and reel packing (picked from 8/9/10/12 pin side) all rights rese r v ed ? c opyright panasonic elect r ic w o r k s co., ltd.
sx (asx) 2. surface-mount terminal 1) tube packing standard packing: tube: 40 pcs.; case: 1,000 pcs. 2) tape and reel packing standard packing: tape and reel: 500 pcs.; case: 1,000 pcs. note: tape and reel packing symbol ?z is not marked on the relay. ? type tape and reel packing (picked from 1/3/4/5-pin side) is also available. rating 1. coil data 1) single side stable type 2) 1 coil latching type 3) 2 coil latching type *pulse drive (jis c 5442-1996) contact arrangement nominal coil voltage single side stable 1 coil latching 2 coil latching part no. part no. part no. 2 form c 1.5v dc asx200a1h asx210a1h asx220a1h 3v dc asx200a03 asx210a03 asx220a03 4.5v dc asx200a4h asx210a4h asx220a4h 6v dc asx200a06 asx210a06 asx220a06 9v dc asx200a09 asx210a09 asx220a09 12v dc asx200a12 asx210a12 asx220a12 24v dc asx200a24 asx210a24 asx220a24 contact arrangement nominal coil voltage single side stable 1 coil latching 2 coil latching part no. part no. part no. 2 form c 1.5v dc asx200a1hz asx210a1hz asx220a1hz 3v dc asx200a03z asx210a03z asx220a03z 4.5v dc asx200a4hz asx210a4hz asx220a4hz 6v dc asx200a06z asx210a06z asx220a06z 9v dc asx200a09z asx210a09z asx220a09z 12v dc asx200a12z asx210a12z asx220a12z 24v dc asx200a24z asx210a24z asx220a24z nominal coil voltage pick-up voltage (at 20 c 68 f ) drop-out voltage (at 20 c 68 f ) nominal operating current [ 10%] (at 20 c 68 f ) coil resistance [ 10%] (at 20 c 68 f ) nominal operating power max. applied voltage (at 20 c 68 f ) 1.5v dc 80%v or less of nominal voltage* (initial) 10%v or more of nominal voltage* (initial) 33.3ma 45 ? 50mw 150%v of nominal voltage 3v dc 16.7ma 180 ? 4.5v dc 11.1ma 405 ? 6v dc 8.3ma 720 ? 9v dc 5.6ma 1,620 ? 12v dc 4.2ma 2,880 ? 24v dc 2.9ma 8,229 ? 70mw nominal coil voltage set voltage (at 20 c 68 f ) reset voltage (at 20 c 68 f ) nominal operating current [ 10%] (at 20 c 68 f ) coil resistance [ 10%] (at 20 c 68 f ) nominal operating power max. applied voltage (at 20 c 68 f ) 1.5v dc 80%v or less of nominal voltage* (initial) 80%v or less of nominal voltage* (initial) 23.3ma 64.3 ? 35mw 150%v of nominal voltage 3v dc 11.7ma 257 ? 4.5v dc 7.8ma 579 ? 6v dc 5.8ma 1,029 ? 9v dc 3.9ma 2,314 ? 12v dc 2.9ma 4,114 ? 24v dc 2.1ma 11,520 ? 50mw nominal coil voltage set voltage (at 20 c 68 f ) reset voltage (at 20 c 68 f ) nominal operating current [ 10%] (at 20 c 68 f ) coil resistance [ 10%] (at 20 c 68 f ) nominal operating power max. applied voltage (at 20 c 68 f ) set coil reset coil set coil reset coil set coil reset coil 1.5v dc 80%v or less of nominal voltage* (initial) 80%v or less of nominal voltage* (initial) 46.7ma 46.7ma 32.1 ? 32.1 ? 70mw 70mw 150%v of nominal voltage 3v dc 23.3ma 23.3ma 129 ? 129 ? 4.5v dc 15.6ma 15.6ma 289 ? 289 ? 6v dc 11.7ma 11.7ma 514 ? 514 ? 9v dc 7.8ma 7.8ma 1,157 ? 1,157 ? 12v dc 5.8ma 5.8ma 2,057 ? 2,057 ? 24v dc 6.3ma 6.3ma 3,840 ? 3,840 ? 150mw 150mw all rights rese r v ed ? c opyright panasonic elect r ic w o r k s co., ltd.
sx (asx) 2. speci?ations notes: *1 this value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load. *2 re f er to 6. conditions f or ope r ation, t r anspo r t and sto r age mentioned in ambient envi r onment. reference data characteristics item speci?ations contact arrangement 2 form c static contact resistance (during initial and electric life tests) max. 100 m ? (by voltage drop of 20 mv 1 ma [1khz]) (by nominal switching capacity: no. of operations: 10 7 ) dynamic contact resistance (during initial and electric life tests) max. 1 ? (by voltage drop of 20 mv 1 ma [1 khz], measurement delay 10 ms after applying nominal coil voltage) (by nominal switching capacity: no. of operations: 10 7 ) contact material stationary contact: agpd+au clad movable contact: agpd rating nominal switching capacity 10 ma 10 v dc (resistive load) max. switching power 0.1 w (resistive load) max. switching voltage 10 v dc max. switching current 10 ma dc min. switching capacity (reference value)* 1 10 a 1 mv dc nominal operating power single side stable 50mw (1.5 to 12 v dc), 70mw (24 v dc) 1 coil latching 35mw (1.5 to 12 v dc), 50mw (24 v dc) 2 coil latching 70mw (1.5 to 12 v dc), 150mw (24 v dc) electrical characteristics insulation resistance (initial) min. 10,000m ? (at 500v dc) measurement at same location as ?nitial breakdown voltage section. breakdown voltage (initial) between open contacts 750 vrms for 1min. (detection current: 10ma) between contact and coil 1,000 vrms for 1min. (detection current: 10ma) between contact sets 1,000 vrms for 1min. (detection current: 10ma) surge breakdown voltage (initial) between open contacts 1,500 v (10 160 s) (fcc part 68) between contacts and coil 2,500 v (2 10 s) (telcordia) temperature rise (at 20 c 68 f ) max. 50 c (by resistive method, nominal coil voltage applied to the coil; contact carrying current: 10ma.) operate time [set time] (at 20 c 68 f ) max. 5 ms [max. 5 ms] (nominal coil voltage applied to the coil, excluding contact bounce time.) release time [reset time] (at 20 c 68 f ) max. 5 ms [max. 5 ms] (nominal coil voltage applied to the coil, excluding contact bounce time.) (without diode) mechanical characteristics shock resistance functional min. 750 m/s 2 (half-wave pulse of sine wave: 6 ms; detection time: 10 s.) destructive min. 1,000 m/s 2 (half-wave pulse of sine wave: 6 ms.) vibration resistance functional 10 to 55 hz at double amplitude of 3.3 mm (detection time: 10 s.) destructive 10 to 55 hz at double amplitude of 5 mm expected life mechanical min. 5 10 7 (at 750 cpm) electrical min. 10 7 (10 ma 10 v dc resistive load) (at 750 cpm) thermal electromotive force max. 3 v (at nominal voltage applied to the coil) conditions conditions for operation, transport and storage* 2 ambient temperature: ?0 c to +70 c ?0 f to +158 f humidity: 5 to 85% r.h. (not freezing and condensing at low temperature) max. operating speed (at rated load) 750 cpm unit weight approx. 2 g .071 oz 1. switching capacity range 2-(1). change in dynamic contact resistance (10 ma 10 v dc resistive load) tested sample: asx20012, 10 pcs. operating speed: 750 cpm measured condition: 10 ms after applying nominal coil voltage, using voltage drop of 20 mv, 1 ma, 1 khz. 2-(2). change in dynamic contact resistance (10 a 1 mv dc resistive load) tested sample: asx20012, 10 pcs. operating speed: 750 cpm measured condition: 10 ms after applying nominal coil voltage, using voltage drop of 20 mv, 1 ma, 1 khz. 10ma 10 a 1mv 10v contact voltage contact current 1,0000 min. 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 max. no. of operations, 10 4 contact resistance, ? 2,0001,0000 min. 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 max. no. of operations, 10 4 contact resistance, ? all rights rese r v ed ? c opyright panasonic elect r ic w o r k s co., ltd.
sx (asx) dimensions (mm inch ) 1. standard pc board terminal schematic (bottom view) 2. surface-mount terminal schematic (top view) external dimensions (general tolerance: 0.3 .012 ) pc board pattern (tolerance: 0.1 .004 ) single side stable/1 coil latching 2 coil latching single side stable/1 coil latching 2 coil latching type external dimensions (general tolerance: 0.3 .012 ) suggested mounting pad (tolerance: 0.1 .004 ) single side stable/1 coil latching 2 coil latching single side stable/1 coil latching 2 coil latching a type 3-(1). change in static contact resistance (10 ma 10 v dc resistive load) tested sample: asx20012, 10 pcs. operating speed: 750 cpm 3-(2). change in static contact resistance (10 a 1 mv dc resistive load) tested sample: asx20012, 10 pcs. operating speed: 750 cpm 1,000 0 10 20 30 40 50 60 70 80 90 0 max. min. max. min. 0 10 20 30 40 50 60 80 90 100 no. of operations, 10 4 contact resistance, m ? n.c. side contact n.o. side contact 2,0001,000 0 10 20 30 40 50 60 70 80 90 0 max. min. max. min. 0 10 20 30 40 50 60 80 90 100 no. of operations, 10 4 contact resistance, m ? n.c. side contact n.o. side contact the cad data of the products with a cad data mark can be downloaded from: http://panasonic-electric-works.net/ac cad data 0.5 1.15 2.54 3.5 0.65 5.08 0.25 15.0 5.08 8.2 7.4 .020 .045 .100 .138 .026 .200 .010 .591 .200 .323 .291 0.5 1.15 2.54 3.5 0.65 5.08 0.25 15.0 5.08 8.2 7.4 .020 .045 .100 .138 .026 .200 .010 .591 .200 .323 .291 5.08 2.54 8-1.0 dia. 10.16 .200 .100 8-.039 dia. .400 5.08 2.54 10-1.0 dia. 12.7 .200 .100 10-.039 dia. .500 single side stable (deenergized condition) 1 coil latching (reset condition) 2 coil latching (reset condition) direction indication 12 10 9 8 1 3 4 5 direction indication 12 10 9 8 1 3 4 5 direction indication 12 10 9 8 7 1 3 4 5 6 cad data 5.08 5.08 2.54 0.65 9.4 0.5 15.0 0.5 8.2 7.4 max.10.0 0.25 1.15 .200 .100 .026 .370 .020 .591 .020 .323 .291 .394 .010 .045 .200 5.08 5.08 2.54 0.65 0.25 9.4 0.5 0.5 8.2 15.0 max.10.0 7.4 1.15 .200 .200 .100 .026 .010 .370 .020 .020 .323 .591 .394 .291 .045 5.08 1.0 2.54 3.16 7.24 .200 .039 .100 .124 .285 5.08 1.0 2.54 3.16 7.24 .200 .039 .100 .124 .285 single side stable (deenergized condition) 1 coil latching (reset condition) 2 coil latching (reset condition) direction indication 12 10 9 8 1 3 4 5 direction indication 12 10 9 8 1 3 4 5 direction indication 12 10 9 8 7 1 3 4 5 6 all rights rese r v ed ? c opyright panasonic elect r ic w o r k s co., ltd.
sx (asx) notes 1. packing style 1) the relay is packed in a tube with the relay orientation mark on the left side, as shown in the ?ure below. 2) tape and reel packing (a type) (1) tape dimensions mm inch (2) dimensions of plastic reel mm inch 2. automatic insertion to maintain the internal function of the relay, the chucking pressure should not exceed the values below. chucking pressure in the direction a: 4.9 n {500gf} or less chucking pressure in the direction b: 9.8 n {1 kgf} or less chucking pressure in the direction c: 9.8 n {1 kgf} or less please chuck the portion. av oid chucking the center of the relay. in addition, excessive chucking pressure to the pinpoint of the relay should be av oided. orientation (indicates pin no.1)stripe stopper (gray) stopper (green) 10.0 16.0 sx relays tape coming out direction .630 4.0 24.0 0.3 .945 .012 0.2 10.8 .008 .425 0.4 relay polarity bar (z type) 2.0 11.5 15.5 1.75 .059 dia. +.004 0 1.5 dia. +0.1 0 .394 .157 .016 .079 .069 .453 .610 2.0 .079 13 dia. .512 dia. 21 dia. .827 dia. 80 dia. 3.150 dia. 380 dia. 14.961 dia. for general cautions for use, please refer to the ?autions for use of signal relays or ?eneral application guidelines? a c b all rights rese r v ed ? c opyright panasonic elect r ic w o r k s co., ltd.
|
